Call now – (02) 9586 3111

Access reports, approvals and certifiers: questions and answers

Questions about disability access reports for DA, CC and CDC in NSW, what certifiers expect, fees, inspections and how planning and the NCC fit together. Each answer is short and links to the page that covers the subject in full. Answers refer to the code in force in NSW: NCC 2022 Amendment 2 until NSW adopts NCC 2025 on 1 May 2027.

All questions and answers

From: How Much Does an Access Report Cost in Sydney? Fees, Fee Drivers and What to Send for a Fixed Quote

What is a mobilisation fee (and is it the same as a deposit)?

In construction contracts a mobilisation fee is an upfront payment that covers the cost of setting the job up before productive work starts: site establishment, plant, insurance and administration. For a consultant the equivalent is an engagement payment that secures a slot and covers file set-up and the initial review.

How much does an access report cost in Sydney?

It depends on the scope the drawings define: building class and size, the approval stage (DA, CC or CDC), drawing quality and revisions, and whether adaptable, Livable Housing or SDA requirements sit on the same project. Sydney Access Consultants does not publish a one-size price list. We quote a fixed fee for a named list of documents after we have seen the drawings and know the approval stage.

What do I need to send to get a fixed quote for an access report?

Send the current drawing set (plus the specification for CC or CDC), the intended lodgement stage, the building classification and use, any consent conditions or earlier certifier RFIs, and whether adaptable, livable or SDA streams apply. With that package an access consultant can price a defined document list instead of guessing at hourly time.

Is a DA access report cheaper than a CC access report?

Usually yes, because the DA report assesses capability on planning drawings while the CC report reviews detailed construction documents. The exact difference depends on the project and the completeness of each set.

Are revisions, site inspections and RFI responses included?

The proposal states what is included. Additional revisions, site time or RFI responses after the initial report are typically additional unless the engagement documents say otherwise.

How long does an access report take?

Turnaround depends on the stage, drawing completeness and current workload. The proposal includes a specific indication once the package is reviewed.

From: Access Report Peer Review NSW: Independent Second Opinion

What is an access report peer review?

It is a short, independent check of the report or Performance Solution, the plans it relied on, the NCC edition and clauses cited, and the Premises Standards and AS 1428 references. The output is a clear list of what is sound, what needs clarification, what is non-compliant and what is at risk.

From: Disability access reports for DA, CC and CDC in NSW

When should we engage an access consultant?

Engage an access consultant while the plan form is still flexible, ideally before DA lodgement, and again when the construction set is coordinated for CC or CDC. Early engagement costs less in redesign than fixing door clearances, ramp geometry, sanitary layouts or parking after a council condition or a certifier RFI.

Do I need a disability access report for a Development Application in NSW?

Yes, commonly, when the proposal must show it can meet disability access requirements. The report assesses the design against the Premises Standards, NCC 2022 Amendment 2 access provisions (including Part D4 and related clauses), AS 1428.1:2021, and any DCP, Housing SEPP or Livable Housing overlay that applies. At DA stage the assessment focuses on spatial capability and items to resolve at CC.

Is a DA access report enough for Construction Certificate approval?

No. A report prepared for development consent is generally not suitable for CC lodgement. CC documentation must be assessed against detailed construction drawings and specifications for compliance with the Premises Standards, NCC access provisions and relevant Australian Standards, consistent with the consent. Reusing a DA-only capability statement risks RFIs, redesign and delay.

What should a lodgement-ready access report for a certifier include?

It identifies the project and documents relied upon, states the standards applied, and records a clear compliance status for paths, entries, ramps, stairs, lifts, parking, sanitary facilities, signage and any adaptable or livable-housing requirements. It gives practical recommendations, a stage-appropriate statement of compliance or capability, and explicit limitations.

From: What certifiers want in a disability access report (NSW checklist)

Can my certifier write the access report instead of an access consultant?

The certifier’s job is to determine the certificate. Many council and PCA checklists still ask for a report from an appropriately qualified access consultant against the Premises Standards and NCC access provisions. A general BCA report may touch access but often lacks elemental statuses, drawing-tied reasons and explicit limitations. Do not assume the certifier will author that specialist report, or that “complies with AS 1428” inside another document will satisfy the checklist.

From: Disability access reports for DA, CC and CDC in NSW

Is it worth engaging an access consultant early, before the certifier issues an RFI?

Yes. Early review catches access conflicts while walls, levels and sanitary cores can still move. Waiting for an RFI often means redesign under time pressure, a revised drawing package, and a fresh report tied to the new revision. Engage on the planning set for DA capability, and again on the construction set for CC or CDC. If a Performance Solution looks likely, involve the Principal Certifier before the access report is finalised.

How much does a disability access report for DA or CC cost in NSW?

We quote a scoped fixed fee after we have seen the drawings and the approval stage (DA, CC or CDC). Drivers include building class and complexity, drawing depth, number of levels and access elements, adaptable / livable-housing / Housing SEPP overlays, any flagged Performance Solution pathway, and drawing revisions to track. A DA capability review is a different scope from a CC or CDC construction-set assessment. We do not publish a one-size price list. The documents define the work.

What is the difference between an access report and a full BCA report?

A BCA report addresses the Code more broadly. An access report concentrates on the Premises Standards, NCC access parts, AS 1428 and related parking, lift and housing overlays. They should be consistent. They are not substitutes.

Does CDC always need an access consultant report?

Not every CDC checklist uses the same words. Where the class triggers NCC access provisions, or the PCA requests verification, a construction-level CDC access report is the safe assumption. If the drawings cannot demonstrate those provisions, the report should record the gap.

From: DA vs CC access report in NSW: what changes and why you cannot reuse the DA report

Can I use my DA access report for a Construction Certificate in NSW?

Generally no. A DA report supports planning consent. A CC is assessed on detailed construction drawings and specifications. Re-lodging a DA-stage report usually does not meet that expectation and can trigger RFIs or delay.

What is the difference between a DA access report and a CC access report?

A DA report focuses on spatial capability so council can grant consent. A CC report checks the documents the builder will use, confirms consistency with consent, and records clear compliance status for access elements. Same standards family. Different purpose, drawing depth and language.

Why did the certifier reject our DA access report?

Common reasons: less-developed drawings; “capable of compliance” language; unresolved fittings and dimensions; design change since consent; or a condition / checklist that requires CC-stage verification. The remedy is a CC-stage report on the current set.

Not always. Some conditions and some checklists do. Many certifiers still request one because the DA report cannot verify the CC documents. Treat a new CC report as the safe assumption once detailed drawings exist.

What if we have multiple Construction Certificates?

Each report should match the scope of the CC being sought. Do not sign off access work that sits in a later stage as if it were complete.

From: How to choose an accredited access consultant in Sydney

What is an accredited access consultant?

An accredited access consultant is an Accredited Member of the Access Consultants Association (ACA, formerly the Association of Consultants in Access Australia, ACAA). Accredited Members have served time as Associate Members, passed the ACA Accreditation Test and take part in the association’s continuing professional development program. You can check any consultant’s status on the ACA’s Find an Access Consultant directory at access.asn.au.

Do Sydney councils require an accredited access consultant?

Some do, by name. Inner West Council’s DCP, for example, asks for an access report by an ACAA-accredited consultant for complex developments. Many other councils ask for a “suitably qualified” or “appropriately qualified and experienced” person, which certifiers and assessing officers commonly read as an accredited consultant. Check your council’s DCP and any consent condition before you engage someone.

What should I ask an access consultant before hiring them?

Ask for their ACA membership class and number and check it, whether they’ve worked on your building class and approval route, which stages their fee proposal covers (DA, CC, inspections, as-built), who will answer the certifier’s questions, whether they can prepare a performance solution if needed, and what professional indemnity and public liability cover they hold.

How much does an access consultant cost?

It depends on the scope, building class, stage and whether a performance solution is needed. We do not publish a one-size price list.

Is ACAA the same as ACA?

Yes. The Access Consultants Association (ACA) is the current name. ACAA was the former name. Older documents may still say ACAA.

From: Mid-construction access inspections in NSW: hold points before linings go on

Is a hold-point access inspection required in NSW?

No. Mandatory critical stage inspections are carried out by the principal certifier. A hold-point access inspection is not one of them. It is a voluntary check that a builder or developer engages to reduce the risk of access defects at the end of the job. Consent conditions or the certifier may ask for an access consultant's statement before the occupation certificate, and a record of earlier inspections makes that statement much easier to give.

When should an access consultant inspect during construction?

At the points where access items are about to be concealed or fixed in place: after set-out and before the slab pour, at frame stage before linings, at sanitary set-out before tiling, and at fit-off before handover.

Is a mid-construction access inspection mandatory in NSW?

No. Critical stage inspections are carried out by the principal certifier. A hold-point access inspection is a voluntary check that reduces the risk of access defects being found at the occupation certificate stage.

What does a pre-lining access inspection check?

Door frame sizes for clear opening width, circulation space at doors, reinforcement for grabrails and future fittings in bathrooms, and rough-in heights for switches and outlets, checked against the approved access report and AS 1428.1 before the walls are closed.

How is this different from the occupation certificate access inspection?

The occupation certificate inspection checks the finished building. A hold-point inspection checks the same items earlier, while they can still be corrected without demolition, and leaves photographic evidence of items that will later be hidden.

What if linings are already on?

We verify concealed items such as bathroom wall reinforcement using non-destructive methods where possible, often with detection technology and by removing switch plates and similar fittings.

From: Multiple Construction Certificates and access reports in NSW

Which NCC edition applies when a NSW building has more than one Construction Certificate?

For a multi-storey building, once a CC has been issued under the same consent for work involving the entrance floor, later CC applications are assessed against the Building Code in force when that entrance-floor CC was applied for. Before then, each CC follows its own application date. This comes from section 19(1A) of the Environmental Planning and Assessment (Development Certification and Fire Safety) Regulation 2021. Confirm the applicable code edition with your Principal Certifier for each certificate.

Does the 1 May 2027 NCC 2025 start date affect our later CCs?

It can. If your entrance-floor CC is applied for before 1 May 2027 and issued, later CCs for the same building generally stay on the earlier edition. If it is applied for on or after 1 May 2027, NCC 2025 applies to it and to later CCs. Each access report should state the edition it assesses against.

Does an earthworks or basement CC need an access report?

Only if the certifier or a consent condition asks for one, or if that CC contains access work. A basement with accessible parking or lift lobbies needs those parts assessed. If the CC contains no access work, we do not automatically issue a scoped statement or report; we assess whether an engagement is needed and advise you.

Does the entrance-floor lock-in also fix the Premises Standards and the AS 1428.1 edition?

The NSW rule locks the Building Code edition for later CCs. The Premises Standards are Commonwealth law, and their Access Code has referenced AS 1428.1:2021 since 29 July 2025. There may be a gap between the two. Discuss it early with your certifier and access consultant.

Who decides which floor is the entrance floor?

The certifier, based on where the principal pedestrian entrance is. Agree it in writing early, especially on sloping sites.

Can one access report cover several CCs?

It is clearer to match each report to one CC, its drawings and its edition.

From: Why is town planning so complicated in NSW, and where does access compliance fit?

Why is town planning so complicated in NSW, and where does access compliance fit?

NSW planning is layered. Each layer was added for a different reason and the old ones were rarely removed, so a single site can be governed by an Act, a Regulation, several State policies, a council LEP, a DCP and overlays. Planning approval does not settle access compliance under the National Construction Code. That is checked later, at Construction Certificate stage or as part of a Complying Development Certificate. Sydney Access Consultants helps builders, developers and architects line the two up early.

Why do the rules keep changing?

Housing targets, low and mid-rise housing reforms, the consolidation of State policies and the move to the NSW Planning Portal have all changed how proposals are assessed. Older DCPs can lag behind a State policy that now overrides them. A sensible order is to check the State policy first, then the LEP, then the DCP, and to have your planner confirm which instrument applies.

Why do setbacks, adaptable housing and parking change at council boundaries?

Greater Sydney's councils each write their own DCP, so access-related design rules can change when you cross a local government boundary, even though the NCC access provisions stay the same across NSW.

How do overlays like heritage, bushfire and flooding affect access?

Each overlay can bring its own referral body and specialist report. Heritage fabric can make a step-free entry hard to achieve without a Performance Solution. Flood planning levels can raise floor heights and create level changes at entries that a ramp or lift then has to resolve. Where a site is bushfire mapped, the access path and entry still have to work with the levels and construction the overlay requires. Settle these early with your planner and certifier.

Does a DA approval mean the building complies with the NCC?

No. A development consent approves the use and the built form under the planning system. Compliance with the National Construction Code, including the access provisions in Part D4 and AS 1428.1, is assessed later, at Construction Certificate stage, or as part of a CDC. Items such as accessible paths of travel, entries and sanitary layouts can come back after the DA if they were not designed in early.

When should I get an access report: DA, CC or both?

Often both. A DA access report tests whether the planning design is capable of meeting the access requirements, including any DCP or Housing SEPP overlays. A CC access report assesses the construction documents against the Premises Standards, the NCC access provisions and AS 1428.1. A DA report is not a substitute for a CC report.

What is the difference between an LEP and a DCP?

The LEP is a legal instrument that sets zoning and the main development standards. The DCP gives more detailed design guidance that council considers when it assesses a DA.

Is a CDC faster than a DA for accessible housing?

A CDC is only available if the proposal meets every standard in the Codes SEPP. Overlays such as flooding, heritage or bushfire can rule it out and take the project back to a DA. Either way, NCC access still has to be met.

Does the Housing SEPP override my council DCP?

State policies can prevail over local controls where they are inconsistent. Your planner should confirm what applies to your site.

Who checks access compliance, council or the certifier?

Council assesses the planning application, including any DCP access items. The registered certifier, or council when it acts as certifier, assesses NCC access at CC or CDC. They are different checks.

From: SSD Access Reports NSW: Answering SEARs on Accessibility

When does an SSD need an access report?

The report is driven by the SEARs. An access report is needed where the issued SEARs raise accessibility, often under built form, design quality or accessibility headings. It is not automatic for every SSD.

From: What certifiers want in a disability access report (NSW checklist)

What does a lodgement-ready report contain?

There is no single clause that requires every NSW project to lodge an access consultant's report. Consent conditions, certifier discretion and council or PCA checklists are the usual triggers. City of Newcastle's Construction Certificate guides, for example, request an appropriately qualified access consultant report for boarding houses and hostels of Class 1b. Similar wording appears where the class triggers NCC access provisions.

What drawings and details are expected?

DA: spatial capability on the planning set. Fittings are often incomplete. The report should say so.

What should the design team send?

site and floor plans, elevations and sections; door and sanitary schedules; ramp, stair and lift details; accessible parking and external works; classification and use; consent conditions and prior RFIs; previous access reports; the lodgement date the certifier is working to

What is the “affected part” and why must the report say so?

When new work in an existing building creates or alters an entrance or path, the Premises Standards treat the continuous accessible path of travel from the principal pedestrian entrance to the new work as the affected part. The report must state what was assessed, what was excluded, and what affected-part logic was applied. Otherwise a certifier may infer whole-building certification from a partial scope.

When must the access report flag a Performance Solution?

If an element cannot meet Deemed-to-Satisfy access provisions, recording non-compliance is not enough for certification. Flag the need for a Performance Solution and a performance-based design brief early. Certifiers are not obliged to accept any alternative. Draft review with the PCA is common practice. Process sits on disability access Performance Solutions.

How should a DtS report and a Performance Solution sit together?

Combination solutions are allowed: some elements DtS, some Performance Solution. The access report should make the split visible so the certifier can see which items rely on the alternative pathway.

Do I need photos and measurements, or are drawings enough?

New work can often be assessed from coordinated drawings and specifications. Existing buildings and affected-part work usually need site notes, photographs and measured checks. If the drawings cannot support a status, the report should say insufficient information.

Who can prepare a report certifiers will accept?

An access consultant with relevant qualifications and experience, typically Certificate IV in Access Consulting and, where it applies, ACAA membership, working to the Premises Standards and the NCC edition in force. SAC reports are signed by Gary Finn, ACAA Accredited Member #435. Gary retained registration as an architect between 1993 and June 2026, and is now concentrating on the disability access consulting branch of his enterprise.

From: When do you need a disability access consultant in NSW?

When do you need a disability access consultant in NSW?

Engage an access consultant when a NSW council DA checklist or DCP requires an Access Report; when the building work must meet the Disability (Access to Premises — Buildings) Standards and NCC access provisions; when a certifier needs documented access assessment for a Construction Certificate or CDC; or when a change of use or major alteration creates an affected-part access obligation. Early concept or pre-DA engagement usually reduces redesign risk compared with responding after an RFI or consent condition.

Is an Access Report mandatory for every NSW DA?

No. It is commonly required when the class or DCP triggers Premises Standards and NCC access provisions, or when the lodgement checklist names an access consultant’s report. Confirm the LGA list for the site.

Can my architect self-assess instead?

The architect remains the author of the design. Many checklists still ask for a separate report from an appropriately qualified access consultant. Do not assume a general BCA summary will satisfy that checklist.

Do I need a new report for CC if I had one at DA?

Usually yes. The DA report is a capability assessment. The CC report verifies the construction set.

What standards does the report reference?

Premises Standards as amended, NCC 2022 Amendment 2 access provisions in NSW (until 1 May 2027), AS 1428.1:2021 where Amendment 2 applies, plus parking, lift and housing overlays that the project actually calls up.

Back to all questions and answers